Orange stain on the side of your home?
We live in Phoenix and have two small children. Our pool is open for the season so I thought I would share this information with you all. Hopefully this article will contribute to at least one less heartbreaking news story.
Swimming pools should always be happy places. Unfortunately, each year thousands of American families confront swimming pool tragedies, drownings and near-drownings of young children. At Whole Home Inspections LLC, we want to prevent these tragedies. These are guidelines for pool barriers that can help prevent most submersion incidents involving young children. These guidelines are not intended as the sole method to minimize pool drowning of young children, but include helpful safety tips for safer pools.
Each year, hundreds of young children die and thousands come close to death due to submersion in residential swimming pools. The Consumer Product Safety Commission (CPSC) has estimated that each year, about 300 children under the age of 5 drown in swimming pools. Hospital emergency-room treatment is required for more than 2,000 children under 5 who were submerged in residential pools. The CPSC did an extensive study of swimming pool accidents, both fatal drownings and near-fatal submersions, in California, Arizona and Florida -- states in which home swimming pools are very popular and used during much of the year.
Swimming pool drownings of young children have another particularly insidious feature: these are silent deaths. It is unlikely that splashing or screaming will occur to alert a parent or caregiver that a child is in trouble. The best way to reduce child drownings in residential pools is for pool owners to construct and maintain barriers that prevent young children from gaining access to pools. However, there are no substitutes for diligent supervision.
Why the Swimming Pool Guidelines Were Developed
Young child can get over a pool barrier if the barrier is too low, or if the barrier has handholds or footholds for a child to use for climbing. The guidelines recommend that the top of a pool barrier be at least 48 inches above grade, measured on the side of the barrier which faces away from the swimming pool. Eliminating handholds and footholds, and minimizing the size of openings in a barrier’s construction, can prevent inquisitive children from climbing pool barriers.
For a solid barrier, no indentations or protrusions should be present, other than normal construction tolerances and masonry joints. For a barrier (fence) made up of horizontal and vertical members, if the distance between the tops of the horizontal members is less than 45 inches, the horizontal members should be on the swimming pool-side of the fence. The spacing of the vertical members should not exceed 1-3/4 inches. This size is based on the foot-width of a young child, and is intended to reduce the potential for a child to gain a foothold. If there are any decorative cutouts in the fence, the space within the cutouts should not exceed 1-3/4 inches.
The definition of pool includes spas and hot tubs. The swimming pool-barrier guidelines, therefore, apply to these structures, as well as to conventional swimming pools.
How to Prevent a Child from Getting OVER a Pool Barrier
A successful pool barrier prevents a child from getting OVER, UNDER or THROUGH, and keeps the child from gaining access to the pool except when supervising adults are present.
The Swimming Pool-Barrier Guidelines
If the distance between the tops of the horizontal members is more than 45 inches, the horizontal members can be on the side of the fence facing away from the pool. The spacing between vertical members should not exceed 4 inches. This size is based on the head-breadth and chest depth of a young child, and is intended to prevent a child from passing through an opening. Again, if there are any decorative cutouts in the fence, the space within the cutouts should not exceed 1-3/4 inches.
For a chain-link fence, the mesh size should not exceed 1-1/4 inches square, unless slats fastened at the top or bottom of the fence are used to reduce mesh openings to no more than 1-3/4 inches.
For a fence made up of diagonal members (lattice work), the maximum opening in the lattice should not exceed 1-3/4 inches.
Above-ground pools should have barriers. The pool structure itself can sometimes serves as a barrier, or a barrier can be mounted on top of the pool structure. Then, there are two possible ways to prevent young children from climbing up into an above-ground pool. The steps or ladder can be designed to be secured, locked or removed to prevent access, or the steps or ladder can be surrounded by a barrier, such as those described above. For any pool barrier, the maximum clearance at the bottom of the barrier should not exceed 4 inches above grade, when the measurement is done on the side of the barrier facing away from the pool.
If an above-ground pool has a barrier on the top of the pool, the maximum vertical clearance between the top of the pool and the bottom of the barrier should not exceed 4 inches. Preventing a child from getting through a pool barrier can be done by restricting the sizes of openings in a barrier, and by using self-closing and self-latching gates.
To prevent a young child from getting through a fence or other barrier, all openings should be small enough so that a 4-inch diameter sphere cannot pass through. This size is based on the head- breadth and chest-depth of a young child.
There are two kinds of gates which might be found on a residential property. Both can play a part in the design of a swimming pool barrier.
Pedestrian gates are the gates people walk through. Swimming pool barriers should be equipped with a gate or gates which restrict access to the pool. A locking device should be included in the gate's design. Gates should open out from the pool and should be self-closing and self-latching. If a gate is properly designed, even if the gate is not completely latched, a young child pushing on the gate in order to enter the pool area will at least close the gate and may actually engage the latch. When the release mechanism of the self-latching device is less than 54 inches from the bottom of the gate, the release mechanism for the gate should be at least 3 inches below the top of the gate on the side facing the pool. Placing the release mechanism at this height prevents a young child from reaching over the top of a gate and releasing the latch. Also, the gate and barrier should have no opening greater than 1/2-inch within 18 inches of the latch release mechanism. This prevents a young child from reaching through the gate and releasing the latch.
Other gates should be equipped with self-latching devices. The self-latching devices should be installed as described for pedestrian gates.
How to Prevent a Child from Getting UNDER or THROUGH a Pool Barrier
In many homes, doors open directly onto the pool area or onto a patio which leads to the pool. In such cases, the wall of the house is an important part of the pool barrier, and passage through any doors in the house wall should be controlled by security measures. The importance of controlling a young child’s movement from the house to the pool is demonstrated by the statistics obtained during the CPSC’s study of pool incidents in California, Arizona and Florida. Almost half (46%) of the children who became victims of pool accidents were last seen in the house just before they were found in the pool.
All doors which give access to a swimming pool should be equipped with an audible alarm which sounds when the door and/or screen are opened. The alarm should sound for 30 seconds or more within seven seconds after the door is opened. It should also be loud, at least 85 decibels, when measured 10 feet away from the alarm mechanism. The alarm sound should be distinct from other sounds in the house, such as the telephone, doorbell and smoke alarm. The alarm should have an automatic re-set feature. Because adults will want to pass through house doors in the pool barrier without setting off the alarm, the alarm should have a switch that allows adults to temporarily de-activate the alarm for up to 15 seconds. The de-activation switch could be a touch pad (keypad) or a manual switch, and should be located at least 54 inches above the threshold of the door covered by the alarm. This height was selected based on the reaching ability of young children.
Power safety covers can be installed on pools to serve as security barriers. Power safety covers should conform to the specifications in ASTM F 1346-91. This standard specifies safety performance requirements for pool covers to protect young children from drowning. Self-closing doors with self-latching devices could also be used to safeguard doors which give ready access to a swimming pool.
When a pool is located completely within a house, the walls that surround the pool should be equipped to serve as pool safety barriers. Measures recommended above where a house wall serves as part of a safety barrier also apply for all the walls surrounding an indoor pool.
An outdoor swimming pool, including an in-ground, above-ground, or on-ground pool, hot tub, or spa, should be provided with a barrier which complies with the following:
1. The top of the barrier should be at least 48 inches above grade, measured on the side of the barrier which faces away from the swimming pool. The maximum vertical clearance between grade and the bottom of the barrier should be 4 inches measured on the side of the barrier which faces away from the swimming pool. Where the top of the pool structure is above grade, such as an above-ground pool, the barrier may be at ground level, such as the pool structure, or mounted on top of the pool structure. Where the barrier is mounted on top of the pool structure, the maximum vertical clearance between the top of the pool structure and the bottom of the barrier should be 4 inches.
2. Openings in the barrier should not allow passage of a 4-inch diameter sphere.
3. Solid barriers, which do not have openings, such as a masonry and stone wall, should not contain indentations or protrusions, except for normal construction tolerances and tooled masonry joints.
4. Where the barrier is composed of horizontal and vertical members, and the distance between the tops of the horizontal members is less than 45 inches, the horizontal members should be located on the swimming pool-side of the fence. Spacing between vertical members should not exceed 1-3/4 inches in width. Where there are decorative cutouts, spacing within the cutouts should not exceed 1-3/4 inches in width.
5. Where the barrier is composed of horizontal and vertical members, and the distance between the tops of the horizontal members is 45 inches or more, spacing between vertical members should not exceed 4 inches. Where there are decorative cutouts, spacing within the cutouts should not exceed 1-3/4 inches in width.
6. The maximum mesh size for chain-link fences should not exceed 1-3/4 inch square, unless the fence is provided with slats fastened at the top or the bottom which reduce the openings to no more than 1-3/4 inches.
7. Where the barrier is composed of diagonal members, such as a lattice fence, the maximum opening formed by the diagonal members should be no more than 1-3/4 inches.
8. Access gates to the pool should be equipped to accommodate a locking device. Pedestrian access gates should open outward, away from the pool, and should be self-closing and have a self-latching device. Gates other than pedestrian access gates should have a self-latching device, where the release mechanism of the self-latching device is located less than 54 inches from the bottom of the gate.
A portable spa with a safety cover which complies with ASTM F1346-91 should be exempt from the guidelines presented here. Swimming pools, hot tubs, and non-portable spas with safety covers should not be exempt from these provisions.
Brought to you by:
David Dion, Managing Member / Certified Professional Inspector® Arizona License #60683
www.WholeHomeInspectiosLLC.com, PHXinspect.com, @PHXinspect #YourHomeTips
Credit to: Nick Gromicko and InterNACHI
This Article was found on https://www.phoenix.gov/news/waterservices/1071
Nov. 24, 2015
There is no better way to celebrate the Thanksgiving holiday than cooking and even frying turkey and all the traditional fixings. But what do you do with the leftover oil, fats and grease? Whatever you do, don't pour it down the drain!
Pouring Fats, oils and grease (collectively known as FOG) down your sink could result in serious damage to residential plumbing and even municipal sewer systems. Instead, take a few short minutes to properly store or trash them.
Store it - Once the oil is cooled, use a coffee filter, cheese cloth or fine metal strainer to filter the oil into an appropriate container. You can then store the oil in the fridge or freezer for up to 6 months for later use.
Trash it - Once the oil is cool, pour it into small, unbreakable, sealable containers and dispose of in the trash. Only throw small amounts of oil into the trash, as big jugs can leak, making a mess of collection trucks and disposal facilities.
It only takes a few small steps to keep your plumbing and the city's sewer system clean this Thanksgiving.
For More Information, visit: http://1.usa.gov/1P7fkXi
Credit to: www.phoenix.gov &
A smoke alarm, also known as a smoke detector, is a device that detects smoke and issues an audible sound and/or a visual signal to alert residents to a potential fire.
Facts and Figures
Smoke Alarm Types
Ionization and photoelectric are the two main designs of smoke detectors. Both types must pass the same tests to be certified to the voluntary standard for smoke alarms, but they perform differently in different types of fires. Detectors may be equipped with one or both types of sensors -- known as dual-sensor smoke alarms -- and possibly a heat detector, as well. These sensors are described as follows:
Individual authorities having jurisdiction (AHJs) may have their own requirements for smoke-alarm placement, so inspectors and homeowners can check with their local building codes if they need specific instructions. The following guidelines, however, can be helpful.
Smoke alarms should be installed in the following locations:
Power for the smoke alarms may be hard-wired directly into the building’s electrical system, or it may come from just a battery. Hard-wired smoke detectors are more reliable because the power source cannot be removed or drained, although they will not function in a power outage. Battery-operated units often fail because the battery can be easily removed, dislodged or drained, although these units can be installed almost anywhere. Older buildings might be restricted to battery-powered designs, while newer homes generally offer more options for power sources. If possible, homeowners should install smoke alarms that are hard-wired with a battery backup, especially during a renovation or remodeling project.
Smoke alarms may also be interconnected so that if one becomes triggered, they all sound in unison. Interconnected smoke alarms are typically connected with a wire, but new technology allows them to be interconnected wirelessly. The National Fire Protection Agency requires that smoke alarms be AFCI-protected.
Inspectors can pass the following additional tips on to their clients:
In summary, smoke alarms are invaluable, life-saving appliances when they are installed properly and adequately maintained.
Brought to you by www.WholeHomeInspectiosLLC.com
Credit to: Nick Gromicko and InterNACHI
Whole Home Inspections, LLC
Get your Free Tips for Homebuyers: